0-1 Inch Measuring Range, 0.0001 Graduation, Friction Thimble, Carbide Face, Multi-Anvil Micrometer

Item Code: 117-107

0.25 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611212-531

0-1 Inch Measuring Range, 0.001 Graduation, Ratchet Thimble, Carbide Face, 15 Degree, Point Micrometer

Item Code: 112-189

0.7 Inch - 1.4 Inch Dial Bore Gage, Indicator Not Included

Item Code: 511-731

0.60 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611196-531

2 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611202-531

0.40 Inch - 1.2 Inch, 0.0002 Inch, Dial Caliper Gage

Item Code: 209-352

0-4 Inch Measuring Range, Ratchet Thimble, 2.5 Inch Base, Mechanical Depth Micrometer

Item Code: 129-127

0-6 Inch Measuring Range, 0.001 Graduation, Ratchet Thimble, Carbide Face, Interchangeable Anvil Micrometer

Item Code: 104-137

1.6 Inch - 2 Inch, 0.00005 Inch, Digimatic Holtest, Titanium Nitride Coated Contact Points, With SPC Output, Ratchet Stop

Item Code: 468-269

2.5 Inch - 3 Inch, 0.00005 Inch, Digimatic Holtest, Titanium Nitride Coated Contact Points, With SPC Output, Ratchet Stop

Item Code: 468-271

0 Inch -1/4 Inch, 0.001 Inch, Mechanical Micrometer Head, 1/4 Inch Diameter Stem with Clamp Nut, Flat Spindle Face

Item Code: 148-204

150 x 150mm Comparator Stand, For Indicators and Linear Gages, Serrated Anvils, 3/8 Inch and 8/20mm Diameter Stem Holes, 275mm Travel, With Fine Feed Adjustment Over Entire Travel

Item Code: 215-505-10

0.03 Inch, Dial Test Indicator, Full Set 0-15-0, 0.0005 Inch Graduation, 3/8 Inch Stems, 0.079 Inch/.039 Inch/.118 Inch Contact Points, Clamp and Hold Bar, 19.9mm Length, Anti-Magnet, Jeweled Bearing

Item Code: 513-402T

0 Inch -1 Inch Outside Diameter, 0.055 Inch - 1.05 Inch Inside Diameter, 0.001 Inch, Mechanical Groove Micrometer, 0.25 Inch Diameter Flange, Non-Rotating Spindle

Item Code: 146-231

2 Inch, Square Steel Gage Block, ASME 0

Item Code: 614202-531

3 Inch, Square Steel Gage Block, ASME 0

Item Code: 614203-531

4 Inch, Square Steel Gage Block, ASME 0

Item Code: 614204-531

0.125 Inch, Square Steel Gage Block, ASME 0

Item Code: 614165-531

0.150 In, Square, Steel, Gage Block, ASME 0

Item Code: 614115-531

0-1 Inch, 0.00005 Inch, IP65 Digimatic Disk Micrometer, .787 Inch/20mm Diameter .028 Inch/0.7mm Edge Thickness Disk, With SPC Data Output, Ratchet Stop

Item Code: 323-350-30

3-4 Inch Measuring Range, 0.0001 Graduation, Ratchet Thimble, Carbide Face, Outside Micrometer

Item Code: 103-218

0-40 Inch(1000mm), 0.0005 Inch(0.01mm), ABSOLUTE Digimatic Caliper, With SPC Data Output, No Thumb Roller

Item Code: 500-507-10

0.03 In, Dial Test Indicator, Basic Set 0-15-0, 0.0005 Inch Graduation, 3/8 Inch Stem, 0.079 Inch Contact Point, 19.9mm Length, Anti-Magnet, Jeweled Bearing

Item Code: 513-402-10E

0.20 Inch, Square Steel Gage Block, ASME 0

Item Code: 614192-531

0.80 Inch, Square Steel Gage Block, ASME 0

Item Code: 614198-531

0.30 Inch, Square Steel Gage Block, ASME 0

Item Code: 614193-531

.50 Inch Plain Jaw, Gage Block Accessory for Inch Square Gage Blocks, 1 Piece

Item Code: 619052

6 Inch, 150mm, Pocket Steel Rule, 1/2 Inch Wide , Pocket Clip, (1/64,1mm)

Item Code: 950-300

0-1 Inch, 0.00005 Inch, IP65 Uni-Mike Digimatic Interchangeable Anvil Micrometer, With SPC Data Output, Friction Thimble, Flat and Rod Anvils Included

Item Code: 317-351-30

0.75 Inch, Square Steel Gage Block ASME 0

Item Code: 614217-531

0.90 Inch, Square Steel Gage Block, ASME 0

Item Code: 614199-531

0.95 Inch, Square Steel Gage Block, ASME 0

Item Code: 614219-531

0-1 Inch Measuring Range, 0.0001 Graduation, Ratchet Thimble, Carbide Face, Ball Anvil Micrometer

Item Code: 115-153

0-6 Inch(150mm), 0.0005 Inch(0.01mm), ABSOLUTE AOS Digimatic Caliper, With SPC Data Output, Carbide OD Jaws

Item Code: 500-174-30

6-7 Inch Measuring Range, 0.001 Graduation, Ratchet Thimble, Carbide Face, Outside Micrometer

Item Code: 103-183

7-8 Inch Measuring Range, 0.001 Graduation, Ratchet Thimble, Carbide Face, Outside Micrometer

Item Code: 103-184

0-12 Inch, 0.001 Inch Dial Caliper, 0.1 Inch/Revolution, White Face, Carbide OD

Item Code: 505-747

5.0mm, Rectangular Steel Gage Block, ASME 0

Item Code: 611615-531

0.20 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611192-531

0.40 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611194-531

0-24 Inch, 0.001 Inch Graduation, Dial Height Gage, With Dual Digit Counters, With Carbide Tipped Scriber

Item Code: 192-152

0.05 Inch, Rectangular Steel Gage Block, ASME 0

Item Code: 611105-531

0-1 Inch Measuring Range, 0.001 Graduation, Ratchet Thimble, Carbide Face, 30 Degree, Point Micrometer

Item Code: 112-237

1/32 Inch - 1/4 Inch, Concave/Convex Radius Gage Set, 15 Pairs of Leaves (1/32 Inch to 1/4 Inch by 64ths), Locking Clamp

Item Code: 186-101

0-1 Inch Measuring Range, 0.0001 Graduation, Ratchet Thimble, Carbide Face, Tubing Micrometer

Item Code: 115-313

Digital Hand Tachometer, Contact Style, 1 to 25,000 RPM

Item Code: 982-551

0 to 1 Inch Range, 0.0005 Inch Resolution, Electronic Drop Indicator

Item Code: 575-123

2 Inch - 3 Inch Dial Snap Gage, 3/8 Inch Stem Diameter, Indicator Not Included

Item Code: 201-153

.25 Inch Half Round Jaw , Gage Block Accessory for Inch Square Gage Blocks, 1 Piece

Item Code: 619051